您好,欢迎来到济南道源丰达机械制造有限公司网站!

服务热线:400-9901-557/18678880998

微信号:18678880998

淘宝店铺:点击进入

1688店铺:点击进入

爱采购商城:点击进入

拼多多商城:点击进入

行业动态 当前位置:首页-行业咨询-行业动态旋转供料器的结构变形怎么办?

旋转供料器的结构变形怎么办?

发布时间:2023-02-22 来源:http://www.sddyfd.com/

旋转供料器旋转阀叶片耐磨性好,锁气性能高、卸料彻底、结构紧凑密切,一般旋转供料器的选型主要是依靠物料的粒径大小,含水量,输送的距离等。由阀体、传动轴、叶片和降低速度器等组成。降低速度电机帮带传动轴和叶轮旋转,因此达到卸灰的目标。它用于将上部料仓中的干燥粉状物料或小颗粒物料蝉联地、平均地喂送到下一设施中去,是一种定量给料设施。
The rotary valve blade of the rotary feeder has good wear resistance, high air-locking performance, complete discharge and compact structure. Generally, the selection of the rotary feeder mainly depends on the particle size, water content and conveying distance of the material. It is composed of valve body, transmission shaft, blade and speed reducer. Reduce the speed of the motor with the drive shaft and impeller rotating, so as to achieve the goal of ash unloading. It is used to feed dry powder materials or small particles in the upper silo to the next facility in a continuous and even manner. It is a quantitative feeding facility.
旋转供料器结构件变形:由于长期使用或操作工操作不当,其压带盖板、顶针、弹簧及其它运动机构产生变形、锈蚀等,从而导致器件吸偏、立片或者吸不到器件,因此应定期检查,发现问题及时处理,以免造成器件的大量浪费,同时安装应正确、牢固地安装在供料部平台上,特别是无旋转供料器高度检测的设备,否则可能会造成旋转供料器或设备损坏。
广东旋转供料器
Deformation of structural parts of rotary feeder: due to long-term use or improper operation by operators, the pressure band cover plate, thimble, spring and other moving mechanisms are deformed and rusted, which may lead to deviation of the device, vertical piece or failure to absorb the device. Therefore, regular inspection shall be carried out to find problems and timely treatment shall be carried out to avoid a large amount of waste of the device. Meanwhile, the installation shall be correctly and firmly installed on the platform of the feeding department, Especially for the equipment without rotating feeder height detection, otherwise the rotating feeder or equipment may be damaged.
润滑不良:一般对供料器的维护与保养,很容易被忽略,但定期的清洁、清洗、加油润滑是必不可少的工作。驱动部分磨损:机械式驱动地靠凸轮主轴驱动供料机构,迅速敲找供料器的击找臂,通过连杆使与之连接的棘轮带动元器件编带前进一个进距,同时带动塑料卷带盘将编带上的塑料带帽离,吸嘴下降完成取件动作。
Poor lubrication: Generally, the maintenance of the feeder is easy to be neglected, but regular cleaning, cleaning, oiling and lubrication are essential. Wear of driving part: the mechanical driving ground drives the feeding mechanism by the cam spindle, and quickly taps the striking arm of the feeder. The connecting rod drives the ratchet connected with it to drive the component braiding forward by one step, and at the same time drives the plastic tape reel to remove the plastic belt cap on the braiding, and the suction nozzle drops to complete the part taking action.
但由于供料机构高速访问供料器,经长时间的使用之后,供料器的棘爪磨损严重,造成棘爪不能驱动卷带盘塑料带正常剥离,使吸嘴不能完成取件工作。因此在安装编带前应仔细检查,对棘爪轮已磨损的旋转供料器应立即修复,不能修复的应及时更换。
However, due to the high-speed access of the feeding mechanism to the feeder, after a long time of use, the pawl of the feeder is seriously worn, resulting in the pawl can not drive the reel plastic belt to peel off normally, making the suction nozzle unable to complete the work of taking parts. Therefore, check carefully before installing the braiding, repair the worn rotary feeder with pawl wheel immediately, and replace it in time if it cannot be repaired.