您好,欢迎来到济南道源丰达机械制造有限公司网站!

服务热线

400-9901-557

0531-83838177

0531-83839177

行业动态 当前位置:首页-行业咨询-行业动态-漩涡髙压鼓风机的组装与应用:

漩涡髙压鼓风机的组装与应用:

发布时间:2022-05-26 来源:http://www.sddyfd.com/

漩涡髙压鼓风机的组装与应用:
Assembly and application of vortex high pressure blower:
1、就把机器设备竖直或立式安装在稳定的地区,防止在运转时因地不整平而不停的震动产生偏倚,要保证 周边环境的清理、干躁、自然通风畅顺等,假如达不了这种应用标准,可采取更好的措施和解决方法,以更风机长期的运作造就有益的标准。
1. Install the machinery and equipment vertically or vertically in a stable area to prevent bias caused by non-stop vibration due to uneven ground during operation. Ensure the cleaning, dryness and smooth natural ventilation of the surrounding environment. If this application standard cannot be reached, better measures and solutions can be taken to create a beneficial standard with the long-term operation of the fan.
2、风机的的转动角度一定与电扇堵盖上所标箭头符号方位一致,此商品是不允许翻转运作的,可是在短期内是还可以的翻转,但应防止长期翻转。
2. The rotation angle of the fan must be consistent with the direction of the arrow symbol marked on the electric fan plug. This product is not allowed to turn over, but it can turn over in a short time, but it should be prevented from turning over for a long time.
3、应用前或查询选取的产品型号是哪样的主要参数,那样在采用的情况下,才可以达到的操纵,如风机在运行工作中时,压力不能超出标识上边标记的稳定工作压力值,以防气泵造成过大的热能和电机超电流量负载造成电机的毁坏。
3. What are the main parameters of the selected product model before application or query, so that the operation can be achieved only when it is adopted. For example, when the fan is running, the pressure cannot exceed the stable working pressure value marked on the mark, so as to prevent the motor from being damaged by excessive heat energy caused by the air pump and excessive electric flow load of the motor.
4、该类髙压漩涡风机除开电机电机转子与离心叶轮处的2个轴承外,其他身体部位没有直接接触磨擦,因此 不容易传出物件碰擦的响声,也不会造成异常响声,如果有便是内部吸进到物品了,就清查取下。
4. Except for the two bearings at the motor rotor and centrifugal impeller, other body parts of this kind of high-pressure vortex fan do not have direct contact and friction, so it is not easy to send out the sound of object collision and will not cause abnormal sound. If there is any, it is the internal suction of objects, so check and remove them.
涡旋式气泵的轴承安装方法具体分二类。一类气泵端轴承安装在电机电动机轴和离心叶轮正中间的泵身体,这类气泵平常不用加润滑油脂。
The bearing installation methods of scroll air pump are divided into two categories. A type of air pump end bearing is installed in the pump body directly between the motor shaft and the centrifugal impeller. This kind of air pump usually does not need to add lubricating grease.
二类气泵端轴承是组装在泵盖正中间,该类气泵端轴承应定时加润滑油脂(7018快速润滑油脂)。针对三班持续作业的气泵理应提升给油频次。该类气泵电机风机端轴承维修保养按一类气泵。
The bearing at the end of class II air pump is assembled in the middle of the pump cover. The bearing at the end of this kind of air pump should be lubricated regularly (7018 quick lubricating grease). The oil feeding frequency of the air pump for continuous operation in the third shift should be increased. The maintenance of the fan end bearing of this kind of air pump motor is based on class I air pump.
维护保养与维护保养:
Maintenance and maintenance:
风机在经由长期的运行以后,出入气两边的滤网和除掉噪音设备应做好清理,以发生免阻塞危害到应用实际效果。此外强烈推荐进排气口外连接采用塑料软管连接(如橡胶软管、塑胶扭簧管),好不必采用硬链接,以防产生振动时危害管路联接。
After long-term operation of the fan, the filter screens on both sides of the air inlet and outlet and the noise removal equipment shall be cleaned to avoid blocking and harm the actual application effect. In addition, it is strongly recommended to use plastic hose connection (such as rubber hose and plastic torsion reed pipe) for the external connection of air inlet and exhaust port. It is not necessary to use hard link, so as to prevent endangering the pipeline connection in case of vibration.
气泵轴承的拆换:拆换轴承务必由了解维修工作中的人开展实际操作。先扭松泵盖紧的螺丝,随后按顶角的次序逐一拆装零件,拆下来的零件应历经清理,随后按反次序安装。
Disassembly and replacement of air pump bearing: the actual operation of disassembly and replacement of bearing must be carried out by people who understand the maintenance work. First loosen the screws on the pump cover, and then disassemble the parts one by one according to the order of the top angle. The removed parts should be cleaned and then installed in the reverse order.
可是一定要留意,在拆装时,不可以硬撬离心叶轮和轴承,应当采用专用型的拉马拉出。在运转时也要留意,风机是禁止固态、液态及有浸蚀汽体进到泵壳,
However, it must be noted that during disassembly and assembly, the centrifugal impeller and bearing cannot be pried hard, and the special Ramallah should be used. During operation, it should also be noted that solid, liquid and etched steam are prohibited from entering the pump casing,
本文的精彩内容由湖北水产增氧设备提供知识提供,本网站还有很多的精彩内容,更多的内容您可以点击进入:http://www.sddyfd.com/我们有专门的客服为您解答问题
The wonderful content of this article is provided by Hubei aquatic oxygenation equipment. There are many wonderful contents on this website. You can click to enter more contents: http://www.sddyfd.com/ We have special customer service to answer your questions